SandCalc

Volume converter · US units

Cubic Yard Calculator: Feet to Yards, Tons & Bags

Free cubic yard calculator. Turn length, width and depth into cubic feet, cubic yards, tons and bags, with tonnage figures for sand, soil, gravel and stone.

Cu yd, tons and bags in one slip Density built in Free, no sign-up
Volume slip Cu ft · cu yd · tons · bags

The slip is pre-filled with a 12 × 10 ft example at 4 inches deep. Type your own measurements and it recalculates as you go.

Estimate—
Coverage area—
Volume before waste—
Order this much (with waste)—
Weight—
Bags —
Estimated material cost—

Enter your measurements to get an order slip you can read at the counter.

What a cubic yard actually is

A cubic yard is a box three feet long, three feet wide and three feet high. That is 27 cubic feet, and 27 is the only number you need to keep in your head: every conversion on this page starts or ends with dividing by 27.

To picture it: a level load in a short bed pickup is roughly one and a half to two cubic yards. A standard contractor wheelbarrow holds about 6 cubic feet, so one cubic yard is four and a half wheelbarrow loads. A cubic yard of sand weighs more than a cubic yard of soil, and a cubic yard of mulch weighs a fraction of either — same box, different contents.

How to use it

  1. Pick the shape that matches what you are covering. Rectangle for beds, pads and driveways; circle for tree rings and fire pits; triangle for a corner cut; or type the square footage if you already measured it.
  2. Enter the depth. This is where almost every wrong order comes from. Four inches is 0.333 feet, not 4.
  3. Set the waste allowance. Ten percent for a flat firm base, fifteen to twenty for anything that will be compacted or dumped unevenly.
  4. Choose the price unit you were quoted in — per yard, per ton or per bag. Suppliers mix these constantly.
  5. Read the bold line. That is the number to order, already including waste.

The formula, in four steps

  • Square feet = length x width. For a circle, 3.14 x radius x radius.
  • Cubic feet = square feet x depth in feet.
  • Cubic yards = cubic feet / 27.
  • Tons = cubic feet x density in pounds per cubic foot / 2000.

That is the whole calculation. The rest of this page is about the two numbers people plug in wrongly: depth and density.

Depth is the number that ruins orders

One inch is 0.0833 feet. Two inches is 0.167 feet. Four inches is 0.333 feet, six inches is 0.5, twelve inches is 1.0.

People read "4 inches" and type 4. That orders twelve times too much material. A 12 x 10 foot pad at a real 4 inches is 40 cubic feet; at a typed 4 feet it is 480. If you remember one thing from this page, make it that the depth field wants feet unless you switch the unit to inches — and the calculator above has a unit switch next to the depth box precisely because of this.

The same volume weighs different amounts

A cubic yard is fixed at 27 cubic feet. Its weight is not fixed at all. For one cubic yard:

  • Sand: about 2,700 pounds, 1.35 tons.
  • Screened topsoil: about 2,430 pounds, 1.2 tons.
  • Garden soil blend: about 2,700 pounds, 1.35 tons.
  • Gravel or #57 stone: about 2,800 to 2,900 pounds, 1.4 to 1.45 tons.
  • Crushed stone dust: about 2,700 pounds, 1.35 tons.
  • Fill dirt: about 2,900 pounds, 1.45 tons or more when damp.
  • Bark mulch: about 800 to 1,000 pounds, 0.4 to 0.5 tons.
  • Compost: about 1,600 to 1,900 pounds, 0.8 to 0.95 tons.

This is why two quotes can look wildly different: one supplier is quoting yards, the other is quoting tons, and neither is wrong. Divide the ton price by the tonnage per yard to compare them on the same basis. A 1.4 ton-per-yard stone at $45 a ton is $63 a yard; a $55 a yard quote for the same stone is the cheaper one.

What a truck holds

Ordering more yards than the truck can carry means two delivery charges, and ordering a load that cannot reach your driveway means a frustrated driver and a returned load.

  • Single axle dump truck: 5 to 6 cubic yards.
  • Tandem axle dump truck: 10 to 15 cubic yards.
  • Tri-axle: 15 to 20 cubic yards.
  • Dump trailer behind a pickup: 3 to 4 cubic yards.
  • Short bed pickup, level load: 1.5 to 2 cubic yards, and it is already at its weight limit with sand.

Two practical rules: a tandem load weighs 13 to 20 tons, which is over the legal limit on plenty of residential roads, and a truck needs about 9 to 10 feet of clear width plus overhead clearance to tip.

Bags per cubic yard

If you are buying bagged material, divide 27 by the bag size:

  • 0.5 cubic foot bags: 54 bags per yard.
  • 0.75 cubic foot bags: 36 bags per yard.
  • 1 cubic foot bags: 27 bags per yard.
  • 2 cubic foot bags: 13.5, so 14 bags per yard.

Bagged material usually costs two to four times the bulk price per cubic foot, so bags are for patches, planters and small jobs where a delivery charge would swamp the order.

A worked example

A 12 foot by 10 foot area, 4 inches deep — the example already in the calculator above.

  • Area: 12 x 10 = 120 square feet.
  • Volume: 120 x 0.333 feet = 40 cubic feet.
  • Yards: 40 / 27 = 1.48 cubic yards.
  • With ten percent waste: 1.63 cubic yards to order.
  • Weight: 44 cubic feet x 100 pounds = 4,400 pounds, or 2.2 tons.
  • Bags: 44 / 0.75 = 58.7, so the slip rounds up to 59 bags.
  • Cost at $35 a yard: about $57.

Notice how small the order is: a job that looks like "a whole patch of ground" is one and a half yards, and any supplier will round it up to two. That rounding is normal and it is cheaper than a second trip.

Pick the page that matches your material

Density changes the tonnage, so each material has its own calculator with its own density table, coverage chart and worked example:

Mistakes that cost money

  • Typing inches into a field that wants feet.
  • Comparing a per-ton quote with a per-yard quote without converting.
  • Forgetting compaction allowance on anything that will be rolled or driven on.
  • Ordering one load bigger than the truck can legally carry on your street.
  • Measuring the footprint of a pile instead of the area you are covering.

Questions people ask

How many cubic feet are in a cubic yard? 27. A cubic yard is 3 x 3 x 3 feet.

How many cubic yards is a ton? It depends on the material. A ton of sand is about 0.74 cubic yards, a ton of topsoil about 0.83, a ton of gravel about 0.7, and a ton of mulch about 2.2.

How many wheelbarrows in a cubic yard? Four to five, for a standard 6 cubic foot contractor barrow.

Is a cubic yard the same as a yard of material? Yes. When a supplier says "a yard" they mean a cubic yard, never a square yard.

How much area does a cubic yard cover? 324 square feet at 1 inch deep, 162 at 2 inches, 108 at 3, 81 at 4, 54 at 6 and 27 at 12 inches.

Should I order extra? Ten percent is the normal allowance for settling. Order more only when the ground is uneven, in which case measure the average depth rather than the deepest point.

Estimates only. Confirm density and price with your supplier before ordering.